|
Planar Monolithic Industries (PMI), a leading
supplier of custom, high-reliability MIC/MMIC components and subsystems for applications
in space, military, communications, commercial and consumer electronics systems
for more than three decades, recently introduced five new products in their extensive
line of RF and microwave components. Included are an 8-12 GHz digitally tuned
phase shifter, a 0.01-20 GHz ultra-low-noise amplifier, a 0.1-18.0 GHz,
digital attenuator w/USB interface, a 0.01-18.0 GHz limiter, and a 0.5-18.0 GHz
SPST reflective coaxial switch. Contact PMI today for more information.
PMI Model No. PS-812-360-14B-SFF OPT10D27, Digitally Tuned Phase Shifter
 PMI Model No.
PS-812-360-14B-SFF
OPT10D27 is a Digitally Tuned Phase Shifter that operates from 8.0 to 12.0 GHz,
optimized for 10.27 GHz, and has a survival input power level of +30 dBm
and an insertion loss of 12 dB. This unit is tuned using 14-bit (+3.3 V RS-422
Control) through a 44-Pin High-Density D-Sub male connector and has SMA female connectors
in a housing of 3.25" x 2.00" x 0.50".
PMI Model No.PLNA-30-10M20-292FF, Ultra-Low Noise Amplifier
 PMI Model Number
PLNA-30-10M20-292FF
is an Ultra-low Noise Amplifier with working frequency range of 10 MHz to 20 GHz
that offers up to +28 dB minimum gain @ 20 GHz with a typical gain flatness
of ±2.5 dB typical and Noise figure of 3 dB @ 0.5 GHz, 2.5 dB
@ 18 GHz, and 3.3 @ 20 GHz. The amplifier's housing size is 0.53" x 0.70"
x 0.26" with 2.92 mm connectors that can be used as a surface mount or connectorized
component.
PMI Model No. ATN-30-100M18G-USB, 0.1 to 18.0 GHz, Attenuator
 PMI Model No.
ATN-30-100M18G-USB
is a state-of-the-art attenuator that operates from 100 MHz to 18 GHz,
offers 30 dB of attenuation in 1 dB steps with insertion loss of typically
5 dB; VSWR In/Out of 2.5:1 and Attenuation Accuracy of ±2.5 dB. This attenuator
is controlled and powered via USB 2.0. Package size is 2.25" x 1.0" x 0.33" and
has SMA female connectors.
PMI Model No. LM-10M18G-16-20W-AL-ROHS, Coaxial Limiter
 PMI Model No.
LM-10M18G-16-20W-AL-ROHS
is a 0.01 to 18.0 GHz Limiter. It has a maximum RF power handling of 20 W
CW, a maximum insertion loss of 2 dB, and a maximum recovery time of 250 ns.
This model has a SMA male/female connectors and a size of 0.90" x 0.38" x 0.38".
PMI Model No. P1T-500M18G-80-R-SFF-SW21841A, SPST Switch
 PMI Model No.
P1T-500M18G-80-R-SFF-SW21841A
is a 0.5 to 18.0 GHz Single Pole, Single Throw, Reflective Switch that offers
a maximum insertion loss of 2.5 dB with a maximum VSWR of 1.9:1 and a minimum
isolation of 80 dB. Housing measures 0.792" x 1.970" x 0.530" and has SMA female
connectors.
About Planar Monolithics Industries (PMI)
Planar Monolithics Industries, Inc., was founded by entrepreneurial technocrat
Dr. Ashok (Ash) Gorwara on November 11, 1989. For over three decades, PMI has been
a leading supplier of custom, high-reliability MIC/MMIC components and subsystems
for applications in space, military, communications, commercial and consumer electronics
systems.
Today, PMI with Quantic's leadership, continues to carry on the legacy of its
founder, Dr. Ash by expanding the applications of RF/Microwave components and subsystems
into new, low cost, RF/Microwave receiving and transmitting systems for both civilian
and military customers.
PMI was founded basically to take advantage of the growing demand in monolithic-based
products using the Hybrid MIC/MMIC technology innovations that are mushrooming in
a big way all over the world. High performance and reliable products can be obtained
by using this technology.
A vacuum exists in the demand for state-of-the-art Hybrid MIC/MMIC Components
and Subsystems. Planar Monolithics will meet these requirements.
Contact:
Sebastian Palacio
VP & General Manager
Quantic PMI (Planar Monolithics)
7311-F Grove Road
Frederick, Maryland 21704, USA
CAGE Code: 05XQ0
Phone: (301) 662-5019
Cell: (301) 455-9897
E-Mail:
sales@pmi-rf.com
Website: https://www.pmi-rf.com
Posted April 26, 2022
|
